Skip to content

Sheet metal forming and bending

From simple brackets to deep enclosures, KeepWin checks the full bend sequence, tool clearance and material springback. Send the formed model and drawing so we can review the flat pattern, critical fits and any finishing or hardware.

Press brake punch and V die forming a sheet metal bend
6,000 mmTandem bend length review
36–320 tfPress brake force range
±0.3–0.5°Bend angle tolerance reference

Match the tool to the bend geometry

Check flange height, return depth and tool clearance. Review marking on visible faces before choosing a tool and process.

CNC V-die air bending

The backgauge locates the sheet. Punch travel sets the angle, and the V opening affects radius, force and minimum flange. Common for brackets and panels.

Gooseneck and segmented tooling

Gooseneck clearance and segmented tooling can help with return flanges, deep U channels and four-sided boxes. Check each formed wall and the path for removing the part.

Hems and Z offsets

Pre-bend and flatten the hem to meet the edge requirement, or review offset tooling for compact rail and panel joints. Confirm the gap, step height and coating clearance.

Press brake capacity and tolerances

The working envelope includes standard and tandem bending. Review part length, tooling load limits and all critical dimensions together.

Press brake envelope and drawing limits
ItemCapability and conditions
Standard and tandem length, force3,100–4,200 mm · 6,000 mm · 36–320 tf
Bend angle, single and cumulative dimensions±0.3–0.5° · ±0.10–0.15 mm · ±0.20–0.30 mm
Initial V-die, hole-to-bend and offset reviewV ≈ 6T–8T · ≥ 2T + R · ≥ 2.5T–3T
Deep channels and interferenceReview gooseneck or sectional tools for deep boxes. Check opening and depth in the bend sequence.

Enclosure, tray and mounting bracket examples

5052-H32 control enclosure

Sequence the louvers, Z offset, bends and press-fit hardware. Check tool access, mounting-hole alignment and areas to mask before the specified finish.

304 stainless drain tray

Review corner reliefs and four flange bends before joining the corners. Check flatness after welding and agree on a leak test if the tray must retain liquid.

SPCC ribbed mounting bracket

Review rib forming before bending. Measure the slotted mounting faces in the final condition and allow for coating at interfaces.

90° air bending calculator

Choose a grade and thickness to look up the 90° tooling, inner radius and flange references. Enter the bend length and actual tensile strength to estimate force across the two listed V openings.

With a verified K factor, bend allowance is estimated for 90° using the listed inner radius range.

Choose a grade and enter positive thickness and length.

Check the actual tool, grain, radius and flange before release. Force uses F ≈ 1.42 × Rm × L × T² ÷ (1,000 × V) in kN for 90° air bending. The shop verifies tool and press loads for the setup.

90° bend radius and flange starting points
ThicknessV-dieSteel / 5052 R304 / 316L R6061-T6 ROuter flange
1.0 mmV6 / V80.8–1.01.0–1.21.5–2.05.5–6.5
1.5 mmV10 / V121.2–1.51.5–1.82.5–3.07.5–9.0
2.0 mmV12 / V161.6–2.02.0–2.53.0–4.09.5–11.5
3.0 mmV20 / V242.5–3.03.0–3.54.5–6.014.5–17.5
4.0 mmV25 / V323.5–4.04.0–5.06.0–8.018.0–22.0

All bend quantities are in mm. Verify radius and flange with the actual material condition and rolling direction.

Sheet material and forming review

Compare grades and stock references. Check the grade, condition, grain and geometry together for bending.

Aluminum alloys

Check the temper and grain. Review 6061-T6 separately for cracking risk and radius.

5052-H32 · 6061-T6 · 1060-H24 · 3003 · 7075

0.5–10.0 mm

Carbon steel

Check the bend sequence, radii and edge protection at the intended load and finish.

SPCC · DC01 · Q235B · SPHC · 65Mn

0.5–16.0 mm

Galvanized steel

Check coating condition on the outside of the bend and the protection required for edges.

SECC · SGCC · DX51D

0.5–16.0 mm

304 / 304L stainless steel

Review grain orientation, springback and allowable die marks on the visible face.

304 / 1.4301 · 304L

304 · 0.4–12.0 mm

316 stainless steel

Confirm the grade and review radius, springback and any required passivation.

316 / 1.4401

0.5–10.0 mm

316L stainless steel

Retain the low-carbon grade callout and check the bend sequence where parts will be welded.

316L / 1.4404

0.5–8.0 mm

Copper and brass

Check temper and the risk of cracking or marking on contact surfaces.

T2 · C11000 · H62 · H65 · C5191

0.2–6.0 mm

Titanium sheet

Confirm grade, grain direction and condition. Review radius, springback and tooling for the actual part.

Grade 2 · Grade 5 (Ti-6Al-4V)

Confirm from the drawing

Compare sheet material families

Choose at least two families for the comparison.

Design for radius, relief and springback

Inner radius and grain direction

Specify alloy, temper and bend line orientation relative to the grain. Review the inner radius against tooling and verify crack-sensitive bends on representative stock.

Bend relief and nearby holes

Use reliefs at bend ends and adjacent flanges. Dimension nearby slots, holes and hardware from the bend and flag shapes and positions that must hold after forming.

Springback and inspection state

After release the angle may change. Define the datums and whether to measure the part free, supported or assembled. Agree critical dimensions spanning multiple bends.

Inspect the formed part and protect its finish

Height, angle and fit checks

Agree the first-article and batch inspection plan. Check height from the specified datum on a granite plate where suitable, and confirm angles or fits in the agreed state.

Masking and separated packaging

Define surfaces and threads to mask before finishing. Protect visible faces and corners, using trays or dividers suited to the part and shipment.

From drawing review to repeat supply

  1. Review the formed model and drawing

    Confirm revision, material condition, bend order and whether the flat pattern is the manufacturing reference.

  2. Cut blanks and trial bend

    Review actual springback, flat pattern fit and tool marks. Approve the first part in the defined inspection state.

  3. Install hardware, join and finish

    Sequence hardware, welding, masking and finish as specified on the drawing and check the final fit.

  4. Release, pack and retain the setup

    Release against the inspection plan. Pack for shipment and retain the revision, tooling and bend sequence for repeat orders.

Lead time references for sheet metal

Confirm the schedule after reviewing material availability, finish, tooling and inspection.

Cut-and-bend prototypes

3–5 business days

Pilot lot

50–500 pcs / 7–12 business days

First production delivery

1,000–10,000+ pcs / 2–3 weeks

Send drawings for a forming and bending quote

Include the formed STEP model and toleranced drawing. Mark critical inner radii, final angles, fit interfaces, visible faces and any finish or hardware.

Forming and bending project brief

Documents requested for review

Attach bend inputs or a material comparison, or select documents needed for review.

Contact and CAD files

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    FAQs

    Can every bend use an inside radius equal to sheet thickness?

    No. Suitability depends on alloy, condition, geometry and tooling. Treat generic rules as a starting point for review.

    Why can a correct CAD shape be difficult to bend?

    A later flange can block the tooling or collide with an already formed wall. The complete forming sequence must be feasible.

    Should measurements be taken while the press holds the part?

    Final acceptance normally concerns the agreed released or assembled condition. Springback and support conditions must be considered.

    What do I send for a part that also needs bending?

    Send the finished STEP model and the toleranced drawing. If a flat pattern is available, indicate whether it controls manufacturing. The team can confirm how to provide the native DXF or DWG during review.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.