Skip to content

Finished product pre-assembly and insertion

Combine machined, molded, printed and sheet metal parts to a released assembly specification. Agree component supply, fastening and insertion controls, functional checks and how sets are packed.

Torque setpoints for tooling review
0.05–5.0 N·m
Example gap target for the first unit
±0.10 mm
First assembly scheduling estimate
2–4 days

Confirm tooling, limits and schedule after the BOM, parts and inspection plan are agreed.

Gloved operator fitting components inside a metal enclosure at an assembly bench

Pre-assembly, kitting, turnkey supply and on-site assembly

Decide which interfaces to assemble, who supplies each component and where the final checks happen.

Engineering criterionIn-house pre-assemblyBOM kittingTurnkey assemblyCustomer site assembly
Suitable scopePre-fit connectors, harnesses and mixed-material interfaces that can be checked before delivery.Pack by set if field adjustment or tool access is needed.Review structural parts, purchased hardware and acceptance as one project.Suitable when installation and final adjustment use the customer’s own line.
Fit and test responsibilityApprove a first assembly and retain agreed interface checks on the assembled unit.Check kit contents; trial fit may be ordered separately.Approve the configuration and agree which functional tests are part of release.Incoming inspection and fit checks are split according to the project plan.
Parts and substitutionsSplit manufactured, bought and customer-supplied parts in the BOM.Set part numbers, quantities per kit and shortage rules.Confirm supplier approval, substitutions and ownership of any long-lead item.The customer controls stock, replenishment and assembly scheduling.
Packing and protectionProtect fitted connectors, painted faces and exposed joints.Separate similar hardware by part number and count each kit.Review the assembled unit’s support and identify the lot on the package.Pack by item and agree how to protect critical features across shipments.

Assembly routes and engineering review

Pre-assembly and kitting split

  • Use pre-assembly for interfaces that can be inspected and tested before shipment. Keep site-installation parts loose if they need field adjustment or would block access. Set a packaging list by kit.
  • Freeze BOM and orientation, mark the items supplied by each party, and approve the packed set against a sample.

Assembly parameters and acceptance criteria

Switch between torque, press fitting, gap measurements and functional checks. Define limits on the actual assembly drawing and first-article plan.

Torque fastening

Typical use
Specify the joint, fastener grade, thread condition and the target torque in N·m. Review the selected tool at the required setpoint.
What to verify
Define tightening sequence and tool checks. Treat a witness paint mark as a visual indicator and verify the locking method and torque separately.
What to verifyTest methodDrawing and acceptance requirements
BOM and component supplyCheck part numbers and revisions against the approved BOM at incoming inspection. Sample according to the agreed plan.Provide the assembly revision, part list and per-set quantities. Identify approved substitutions, customer-supplied parts and how shortages or revisions are handled.
Fastening and seatingVerify tool output against the intended setting and check the first assembled joint or fitted insert in its final state.Specify torque in N·m with tool and fastening order, or insertion force in N and finished seating height. Verify on the first unit, with lot recording where required.
Fit and functional acceptanceUse a feeler gauge, depth gauge or optical method as suitable. Validate the agreed functional limits on the released configuration.Measure gap and flushness at named points in mm in the specified support condition. Define latch engagement, orientation or continuity checks and sampling separately.
Traceability and packingUse a pack-out checklist. For ESD-sensitive parts agree suitable handling and packaging, and verify labels and protection before release.Map unit or lot identifiers to the BOM revision and inspection record. List loose parts and protect connectors, decorative faces and any ESD-sensitive items as specified.

Technical references · ISO 5393:2017 · IEC 60529 · IEC 61340-5-1:2024

Typical pre-assembly and kitting examples

Use these examples to identify the assembly interfaces, supplied parts and inspection record needed for your design.

Enclosure connectors, harness and clips

Verify routing, connector keying, latch and strain relief. Keep wires clear of cover edges and define the state of the cover and any continuity checks.

Mixed-material panel and perimeter seal

Check the gasket path and compression at corners, panel gap and access for fasteners. Trial on the actual machined frame and molded cover.

Counted hardware and installation kit

Separate visually similar hardware by thread, length or finish. Count against the released BOM revision and mark the bag or compartment.

Torque verification, incoming checks and protected packing

Tool verification and witness marks

Use an appropriate torque tester at the intended setting. Agree verification after start-up, adjustment or a tool change as needed; record results and use approved witness paint where requested.

Incoming inspection and revision control

Match supplier part numbers, revisions and quantities to the BOM. Check agreed visual or dimensional features and segregate shortages, mismatches and unapproved alternates.

ESD and interface protection

For sensitive parts, agree ESD handling and suitable packaging. Use protective caps or separated compartments where appropriate and make the lot traceable after packing.

From BOM review to lot release

  1. BOM and supply review

    Freeze BOM, supply responsibility and delivery state.

  2. Fixture verification and trial build

    Review locating fixtures, tool access and installation sequence.

    2–4 days · First assembly scheduling estimate

  3. First-article and functional approval

    Approve the first assembled unit and the agreed test limits.

  4. Batch assembly and kit release

    Link lot records to the packed kits and release.

    5–10 days · Batch assembly scheduling estimate

Frequently asked questions

Can customer-supplied components be included?

Provide the model, revision, quantities and incoming check plan. Agree the handling of shortages and substitutions before starting assembly.

How is the first assembly approved?

Approve mating fit, orientation, cosmetic condition and any defined functional checks against the specified revision. Record deviations before batch release.

Does a pressure leak check establish IP67 or IP68?

Agree pressure, hold, test medium and leak limit for production screening. When an IP rating is required, separately verify the complete enclosure under IEC 60529 and the project conditions.

Can standard parts be sourced for assembly?

List the manufacturer, part number, finish and permitted equivalent for each purchased item. Confirm procurement, availability and approval of alternatives in the quote.

What if mixed-process parts interfere at trial build?

Record the affected datums, measurements and assembly revision. Review an approved change to geometry, sequence or tooling and repeat the affected checks before release.

How are similar fasteners kept apart in kits?

Assign one identified compartment or bag per part number. Verify thread and length where risk warrants, and reconcile counts with the BOM revision before sealing.

Send drawings for engineering review

Send the assembly drawing, approved BOM and batch size. Include supplied items, tightening or insertion requirements and checks required at release.

Engineering review brief

Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.