Skip to content

Production CNC machining

Plan repeat batches around an approved drawing, fixtures and inspection criteria. Coordinate machining, finishing and protected releases under one production plan.

Send CAD, a controlled drawing, initial lot and forecast. Ask for a quote that itemizes tooling, machining, finishing, inspection and packing.

Tray of machined shafts and housings arranged in individual pockets
50,000–300,000Typical monthly planning · smaller precision parts
3,000–25,000Typical monthly planning · complex multi-axis parts
Cpk ≥1.33 / ≥1.67CTQ capability targets, by agreement
3–6 monthsBuffer-stock planning window by agreement

Separate one-time tooling costs from the unit price

Compare setup time, changeovers and repeatability against the forecast. Agree who owns, maintains and stores dedicated tooling in the quote.

Multi-station fixtures and production feeding

A multi-station fixture can reduce load and unload time when parts share a datum and tool path. For suitable turned parts, assess bar feeding and collection against the required lot and inspection plan.

Fixture or routeWhen to assessSetup and cost factors
Standard vice or soft jawsPrototype and validation lots · 1–50 pcsStraightforward to adapt while the drawing changes. Check manual load time and locating consistency.
Multi-station quick-change toolingAfter the design is frozen and repeat demand is knownCompare parts per setup, cycles, datum repeatability and amortization across planned releases.
Dedicated fixtures and gaugesRecurring production with agreed volume and controlsReview loading access, gauge validation, maintenance costs and the approved handover plan.

Four batch-production examples

Use these example geometries to identify which features need repeatable setups, treatment controls or inspection at lot release.

Multi-port manifold block

Locate multiple faces from the same datum where practical. Include cross-hole breakouts in the deburring plan.

Drawing and inspection
Plan positional checks for the ports, thread gauging and the specified internal edge inspection.

Precision valve shafts and sleeves

Review bar-fed turning, tool wear and the matching shaft and bore fits. Keep material heats identifiable throughout the lot.

Drawing and inspection
Agree measurement sections, gauging method and sorting or sampling by feature.

Finned housing with masked interfaces

Define racking contact points and which threaded or locating features must be protected during anodizing.

Drawing and inspection
Check final fits, coating thickness and agreed appearance using an approved reference.

Polymer rails and bushings

Plan support during machining and define how parts are conditioned and measured after unclamping.

Drawing and inspection
Review straightness, critical bore dimensions and edge condition on the finished part.

Dedicated cutting and drilling for repeat batches

For stable hole groups and stock lengths, compare dedicated semi-automatic or automatic machines with a flexible CNC setup. Assess feed, turning over the part and fixture cost against repeat order volume.

Stock and datum

Specify incoming length, section, straightness and the datum used after each repositioning. Confirm stops and clamping marks on visible surfaces.

Hole and edge checks

Define diameter, depth, spacing, positional tolerance, the acceptable burr and whether reaming, tapping or countersinking is required.

Repeat-batch inspection

Verify first and last pieces at the agreed frequency. Use gauges for critical holes and review the impact of drill wear or a fixture change.

Plan capacity, release schedules and change approval

Use actual part geometry, setup and inspection time to reserve capacity. Agree the first release, forecast horizon and approval for any drawing or material change.

CNC production, releases and tooling assets
ItemCapability and conditions
Typical monthly planning, smaller parts / complex multi-axis50,000–300,000 pcs · 3,000–25,000 pcs
Prototype and validation quantities1–50 pcs (EVT/DVT)
Economic lot, Swiss turning / multi-axis milling1,000–5,000+ pcs · 100–500+ pcs
Blanket orders and call-offsQuarterly or annual agreements with weekly or biweekly releases. Review buffer stock and drawdown window, typically 3–6 months.
Dedicated fixtures and gaugesCustomer-paid tooling assigned to the customer under the agreement. Identify, store, maintain, calibrate and transfer dedicated assets per the order.

Planning capacity depends on programming, cycle time, part geometry and inspection. Confirm reserved volumes and delivery schedule in the quote.

Order controls and document handling
ItemCapability and conditions
Delivery terms by written agreementEXW, FCA, FOB, DAP or DDP may be agreed for suitable shipments. Confirm schedule, quantity tolerance, packaging and acceptance window in the order.
Written approval for substitutionsReview grade, source, condition and recycled content against the drawing. Submit data sheets, compliance evidence and engineering impact for written approval before a substitution.
Engineering and process changesReview customer drawing revisions in 24–48 hours, including stock, cost and first article impact. Agree notice window, verification and written release before major process changes.
NDA, access and recordsMutual NDA and restricted drawing access are available. Retention and destruction follow agreed project terms and regulatory requirements.

Plan SPC and lot traceability

Choose the inspections and records you need. The selections appear in your inquiry brief.

First-off, in-process and release checks

Set check frequency and recheck triggers for tool wear, fixture changeovers and shifts after finishing. Link lot and drawing revision to the release records.

CNC inspection, traceability and report options
ItemCapability and conditions
Raw material and identificationMTR / EN 10204 3.1 · PMI
First article and dimensional reportsAS9102 FAI Form 1/2/3 · CMM · VMM
Production process capabilitySPC / Cpk ≥1.33 · Cpk ≥1.67
Finish reports and batch documentationNSS · HRC / HV · Ra / Rz · COC · RoHS · REACH · CMRT
Supplier qualification documentationRequest applicable certificates by manufacturing entity and scope, calibration records and redacted report samples through the project audit.

Agree CTQs, measurement system, sampling and stability first. Higher Cpk targets apply only to validated features.

Select grades and control lot consistency

Select up to four grades for comparison and the inquiry brief. If a different grade or stock condition is required, specify it on the drawing or in the project notes.

GradeBatch production checksFinishing optionsLot release and traceability
6061-T6 · AluminumConfirm T6 temper and support thin walls to preserve final dimensions.Anodizing, conversion coating or as-machined condition.Keep the temper and material lot identified. Sign off appearance and masked features when specified.
7075-T6 · AluminumConfirm T6 stock condition and review corrosion exposure and any required finish.Anodizing, conversion coating or as-machined condition.Keep the temper and material lot identified. Sign off appearance and masked features when specified.
304 · Stainless steelControl tool wear and work hardening. Confirm that 304 matches the intended exposure.Grade-specific passivation, electropolishing or mechanical finish.Link the heat number to the part lot and confirm the finished surface.
316 · Stainless steelReview the service medium and track the specified 316 stock by heat.Grade-specific passivation, electropolishing or mechanical finish.Link the heat number to the part lot and confirm the finished surface.
316L · Stainless steelVerify the low-carbon grade against the certificate and keep it distinct from 316 through handling.Grade-specific passivation, electropolishing or mechanical finish.Link the heat number to the part lot and confirm the finished surface.
Grade 2 · TitaniumConfirm commercially pure titanium Grade 2 and review clamping at thin features.As-machined, or specified coating or heat treatment after review.Keep Grade 2 and Ti‑6Al‑4V Grade 5 separate from receipt to release.
Grade 5 (Ti-6Al-4V) · TitaniumConfirm the Ti‑6Al‑4V condition and review cutting heat, tool wear and finish.As-machined, or specified coating or heat treatment after review.Keep Grade 2 and Ti‑6Al‑4V Grade 5 separate from receipt to release.
4140 · Carbon and alloy steelDefine heat-treated condition and leave finishing allowance where needed.Heat treatment, grinding or protective coating by drawingVerify specified hardness and fit after heat treatment.
C36000 · BrassConfirm the stock grade and limits for the application and service fluid.As-machined or plating per applicationTrack the stock lot and any applicable lead-content requirement.
POM · Engineering plasticsDefine the exact POM grade, support slender sections and check dimensions after unclamping.As-machined with edge treatment. Stress relief is evaluated by grade and geometry.Identify each material lot and agree temperature and conditioning for final inspection.
PEEK · Engineering plasticsIdentify the PEEK grade and any filler. Set the machining and inspection plan for that stock.As-machined with edge treatment. Stress relief is evaluated by grade and geometry.Identify each material lot and agree temperature and conditioning for final inspection.
PEI · Engineering plasticsConfirm the PEI grade and the conditioning required for dimension checks.As-machined with edge treatment. Stress relief is evaluated by grade and geometry.Identify each material lot and agree temperature and conditioning for final inspection.

Compare selected grades

Choose at least two grades to compare them side by side.

View the full CNC material catalogue ↗

Six stages from drawing freeze to rolling releases

Agree on the input, decision and release record at each stage. Use the approved revision and process baseline when planning repeat orders.

Drawing freeze

Engineering input
Matching CAD and 2D drawing, release quantities and forecast.
Review decision
Confirm CTQs, datums, treatment and masking.
Deliverable
Approved drawing revision and itemized quote.

Protect finished parts and plan the next release

Use separated pockets, sleeves or corrosion protection as the application requires. Agree labels and shipment records, then schedule weekly or biweekly releases against the approved forecast.

Request an itemized production quote

Include your first lot, expected annual quantity and release cadence if known. Attach your selected grades and quality documents to the drawing inquiry.

Your production inquiry brief

Select materials or quality documents above.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.