Skip to content

Custom injection molding services

Choose a molding route and define acceptance before you commit to tooling. Review thermoplastics, liquid silicone rubber, two-shot and insert molding, plus finishing and assembly, in one drawing inquiry.

Molding services and engineering support
9
Rapid-tool T1 trial, working days
10–15
Selected PC, ABS and PC/ABS fits
±0.015–0.030 mm

Tooling schedule and tolerance targets depend on the drawing, resin grade and validation plan.

Injection molding cell with a mold and robotic handling equipment

Nine injection molding services

Open each service for capabilities and examples. Add any combination of routes to your drawing inquiry.

Plastic Injection Molding

Housings, clips and structural components. Review wall transitions, resin shrinkage, gates and visible surfaces before tooling.

Service details

Liquid Silicone Rubber Molding

Seals, valves and flexible components. Confirm Shore A hardness, parting-line flash, grade documentation and any post-cure.

Service details

Overmolding Services

Grips, keypads and soft seals. Compare transfer and two-shot routes, then verify adhesion and mechanical interlock on the selected pair.

Service details

Insert Molding Services

Threaded bushings, terminals and busbars. Define location, anti-rotation, shut-offs and pull-out or torque verification.

Service details

Family & Multi-Cavity Molding

Matching part sets or high-demand single parts. Review fill balance and part ratios before committing to an interchangeable or multi-cavity layout.

Service details

Prototype Injection Molding

Test shrinkage, weld lines and fit with the intended resin. Compare aluminum tooling and quick-change inserts, and reserve room for revisions.

Service details

Production Injection Molding

Plan cavity count, resin supply, tool life and repeat deliveries after the trial and first-article release.

Service details

Injection Molding Quality & Inspection

Agree first-article scope, cavity identification, dimensional inspection and lot traceability from the drawing.

Service details

Secondary Operations for Molded Parts

Review heat-set inserts, ultrasonic welding, printing or marking, and subassembly with the required cosmetic and functional checks.

Service details

From prototyping to hardened production tooling

Compare tooling investment, T1 timing, revision cost and repeat demand. Use the part drawing and resin to set tolerance targets.

Process optionsTooling and mold classFirst trial or sample timingVolume planning referenceBest use and revision trade-off
CNC / 3D printing validationNo injection moldConfirm by projectConfirm by projectCheck assembly interference and appearance while the design is changing. Use molded samples to confirm knit lines and shrinkage.
Rapid trial tool7075-T6 / MUD · SPI 105 Al10–15 business days20–50 pcs
Trial samples
Qualify flow, fit and appearance in the target unfilled resin. Leave room for steel-safe or insert changes.
Bridge steel toolP20 / 718H · SPI 1043–4 weeks500–3,000 pcs
Pilot lot after approval
Pilot supply with production-like slides and texture when needed. Confirm the route against wear, part geometry and revision frequency.
Hardened production toolS136 / 8407 · SPI 101 / 1024–6 weeks10,000–500,000+ pcs
First production lot
Use repeat demand, cavity count, wear and cosmetic requirements to justify the tooling investment. Agree lifetime and maintenance in the tooling order.
Dedicated LSR, two-shot or insert toolDefine shut-offs, feeding and cavity layout by partConfirm by projectConfirm by projectValidate sealing, adhesion, or insert position and retention on the real material combination.

T1 refers to the first mold trial. Sample shipment, revision and production release are scheduled separately. These volumes are planning references. Estimate the cost crossover from tooling, unit price, revisions and expected repeat orders.

Resin families and surface compatibility

Review heat and chemical exposure, shrinkage and visible surfaces before freezing the grade. The catalog lists candidate grades by family.

Samples of molding materials and surface finishes

General thermoplastics

ABS and PP suit different load and chemical conditions. Qualify texture on the molded part, and validate pretreatment where PP is printed or painted.

Grade examples
Chi Mei PA-757 · Moplen HP500N
Browse materials and grades

Resins are grouped by family. For overmolding and inserts, review adhesion and processing temperatures for the complete assembly.

Confirm the exact grade, stock form and requirements with your drawing before quoting.

General-purpose thermoplastics

Plastic Injection Molding

ABS
  • Cycolac MG47
  • Lustran 348
  • Lustran 348-012002
  • Lustran 433
  • Polylac PA 765
  • Polylac PA-746
  • Polylac PA-765
  • RTP 605
  • Terluran GP-22
ASA
  • Luran S 777K
HDPE
  • Dow DMDA 8907 NT7
  • Marlex 9006
LDPE
  • Dow LDPE 722
LLDPE
  • Dowlex 2517
UHMWPE
  • Plaslube PE 4000 NAT
PP
  • Maxxam FR PP
  • Maxxam PPC-20T
  • Pinnacle PP 1112
  • Profax 6323
  • Profax 6523
  • Profax PD702
  • Profax SG-702
  • Profax SR549M
  • RTP 150 CC FR A
  • Thermylene P6-30FG-0600
PS
  • Styron 498
  • Styron 666D
Transparent and impact-resistant thermoplastics

Plastic Injection Molding

ABS/PC
  • Bayblend FR 110
  • Bayblend FR3010
  • Bayblend FR3010 NAT
  • Bayblend T65 XF
  • Bayblend T85 XF
  • Cycoloy C1200HF
  • Cycoloy C2950
  • Cycoloy C6200
  • Cycoloy C6600-111
  • Pulse 2000EZ
PC
  • Hylex P1025L
  • Lexan 121
  • Lexan 141
  • Lexan 3412R
  • Lexan 925U
  • Lexan 940
  • Lexan 940A
  • Lexan EXL9330
  • Lexan HP1
  • Makrolon 2258
  • Makrolon 2405
  • Makrolon 2407
  • Makrolon 2458
  • Makrolon 2558
  • Makrolon 6455
  • Makrolon 6485
  • Makrolon 6555
  • Makrolon 8325
  • Makrolon 9415
  • Makrolon RW6265 X
  • Makrolon RX1805
  • Makrolon RX2530
  • RTP 301
  • RTP ESD C 380 FR L
PC/PBT
  • Xenoy 6620
PC/PET
  • Makroblend EL703
Copolyester
  • Tritan MX711
  • Tritan MX731
  • Tritan TX1001
PET
  • Rynite 530
  • Rynite 935
  • Rynite FR 945
  • Rynite FR515 BK507
  • Rynite FR530
  • Rynite FR530 BK507A
PETG
  • Eastar 6763
PMMA (Acrylic)
  • Plexiglas V825
Engineering thermoplastics

Plastic Injection Molding

PA (Nylon)
  • Grilamid TR55
  • Hylon Select N1000EHL BK
  • Hylon Select N1013HL
  • Hylon Select N1033HL
  • Minlon 10B40 BK061
  • Nymax 1010 A
  • Nymax 600 A Zip 43
  • Nymax GF 1200 A 55 HS Black 13
  • Nymax GF 600 A 33 Blk 28 V
  • Nymax GF 600 A 33 Nat
  • Nymax GMF 604 40 UV Black 28
  • RTP 200
  • RTP 200 UV
  • RTP 203 FR
  • RTP 204 UV
  • Stanyl TW341
  • Vydyne R533H
  • Zytel 101L
  • Zytel 103HSL
  • Zytel 70G13 HS1L BK031
  • Zytel 70G13 HS1L NC010
  • Zytel 70G33HS1L
  • Zytel 70G33HS1L BK031
  • Zytel 7335F NC010
  • Zytel 73G15L
  • Zytel 77G33L
  • Zytel 8018 HS
  • Zytel 80G14AHS BK099
  • Zytel 80G14AHS NC010
  • Zytel FR50 BK505
  • Zytel FR7026V0F BK001
  • Zytel ST801
PPA
  • Zytel HTN 51G35HSL BK083
  • Zytel HTN 51G35HSL NC101
PBT
  • Crastin S600F20
  • Valox 357
  • Valox 420 SEO
  • Valox 420SEO
POM (Acetal)
  • Celcon M90
  • Delrin 500P
  • Delrin 520 MP
  • Delrin 577
  • RTP 800 GB 10
  • RTP 800 GB 20
PPE/PS
  • Noryl 731F-701S
  • Noryl 731S
High-performance resins

Plastic Injection Molding

PEEK
  • Victrex 450G
PEI
  • RTP 2100 LF
  • Ultem 1000
  • Ultem 2200
  • Ultem 2300
PPS
  • Fortron 1140L4
  • Fortron 1140L4 Nat
  • Ryton R-4
  • Ryton R-4-200BL
  • Ryton R-4-200NA
PPSU
  • Radel R-5000 NT
  • Radel R-5100
  • Radel R-5100 BU1027
  • Radel R-5100 GY1037
  • Radel R-5100 NT15
PSU
  • Udel P-1700
  • Udel P-3703 NT 11
LCP
  • Vectra E130I
Thermoplastic elastomers

Overmolding Services

ETPU
  • Isoplast 202EZ
SBC
  • K-Resin KR01
TPC-ET
  • Hytrel 3078
TPE/TPV
  • Santoprene 101-55
  • Santoprene 101-64
  • Santoprene 101-73
  • Santoprene 101-87
  • Santoprene 111-35
  • Santoprene 111-45
  • Santoprene 201
  • Santoprene 201-55
  • Santoprene 201-87
  • Santoprene 211-45
  • Santoprene 251-70W232
  • Versaflex CL2250
  • Versaflex OM 1040X-1
  • Versaflex OM 1060X-1
  • Versaflex OM 6240-1
  • Versaflex OM 6258-1
TPU
  • Texin 245D
  • Texin 983A
Liquid silicone rubber and fluorosilicone

Liquid Silicone Rubber Molding

LSR (liquid silicone rubber)
  • Dow Corning MS-1002
  • Elastosil 3003/30 A/B
  • Elastosil 3003/40 A/B
  • Elastosil 3003/50 A/B
  • Elastosil 3003/60 A/B
  • Elastosil 3003/70 A/B
  • Elastosil 3003/80 A/B
  • Liveo C6-550
F-LSR (liquid fluorosilicone)
  • Silastic FL 60-9201

Inspection conditions and traceable records

Metrology lab setup for molding inspection

Dimensional tolerances and conditioning

Agree the referenced standard edition, drawing datums and resin conditioning. Use ISO 20457 for applicable molded plastics and ISO 3302-1 where appropriate for molded rubber. Define optical or cosmetic limits on the drawing or approved master.

Measurement and functional tests

Select CMM, optical measurement or gauges to suit the feature. Agree fixturing for soft parts and the method for leak, peel, torque or pull-out testing where needed.

Cavity-level validation and process control

Label samples by cavity. Match the first-article plan to critical features and agree sampling or capability studies when the process is stable. Control any regrind by written approval.

Material and release documentation

Specify resin grade, lot traceability, COA and the requested FAI or PPAP scope. Verify compliance evidence for the exact grade, use and production route.

Technical references · ISO 20457:2026 · ISO 291:2008 · ISO 3302-1:2014

Manufacturing capabilities

Use these figures for an initial review. The approved drawing, process route and quote set the requirements for the part.

Press and part envelope
ItemCapability and conditions
Electric thermoplastic presses50–350 tf · 30–1,100 g · 450 × 450 × 200 mm
Large thermoplastic presses450–1,300 tf · 1,500–6,500 g · 950 × 750 × 400 mm
Two-shot presses120–450 tf · 80–800 g + 50–500 g · 350 × 300 × 150 mm
LSR presses50–250 tf · 15–450 g · 300 × 300 × 120 mm
Tool fit and wall rangeSmall electric presses: min. mold height 150 mm, tie-bar spacing up to 760 × 760 mm and typical walls 0.6–3.5 mm. Large press span up to 1,350 × 1,250 mm. Two-shot table Ø650–1,150 mm. LSR platen up to 600 × 600 mm.

Rows show clamp force, shot mass and part envelope. Material, tool fit and usable shot size are evaluated together.

Injection resins and traceability
ItemCapability and conditions
ABSChi Mei PA-757 / PA-747 · LG HI121H · SABIC Cycolac MG47 / FR15U
PCCovestro Makrolon 2405 / 2805 / 2458 · SABIC Lexan 141R / 940A / EXL1414
PC/ABSCovestro Bayblend T65 XF / FR3010 · SABIC Cycoloy C2950 / MC1300
PA6 / PA66 / PA12 / PPABASF Ultramid B3S / A3EG6 · Zytel 101L / 70G33L · EMS Grilamid TR90
POM / PPHostaform C9021 · Delrin 100P / 500P · Moplen HP500N · Formosa 1120 · SABIC PP 575P
PEEK / PPSU / PEI / PBT / TPU / TPEVictrex 450G · Radel R-5000 · ULTEM 1000 / 1010 · Kraiburg TPE
Customer-supplied or specified resinGrade, origin and lot can be specified. Regrind or substitution requires written approval.
Grade-specific documentsCOA, TDS and SDS. For relevant grades, request filler content, UL 94 Yellow Card by thickness, transmittance, haze or contact-compliance documentation.
Tool steel, cavity layout and service life
ItemCapability and conditions
Corrosion-resistant or high-polish toolingS136 / Stavax ESR · HRC 48–52 · 1.2083 / 1.2316
Wear-resistant tooling8407 / Orvar Supreme · HRC 48–52 · NAK80 HRC 37–41 · ASP-23 / HAP40
Prototype or short-run toolingP20 / 718H HRC 30–36. 7075-T6 aluminum tooling for selected unfilled resin prototypes.
Cavities and runner balance1 / 2 / 4 / 8 / 16 / 32 / 64 cavities; family tools with adjustable flow and valve-gated hot runners as required.
SPI 101 / 102 / 103≥1,000,000 · 500,000–1,000,000 · 100,000–500,000
SPI 104 / 10510,000–100,000 · Al 5,000–10,000
Customer tool ownership and transferCustomer ownership after payment as contracted, with drawings, asset identification, cycle counter, preventive maintenance and transfer support.

The listed cycle figures are planning ranges. Define the required life, resin and maintenance conditions when ordering the mold.

Molded part tolerances and inspection
ItemCapability and conditions
Noncritical features up to 30 mm±0.05–0.10 mm
Critical fit in PC, ABS and PC/ABS±0.015–0.030 mm
Critical dimensions in PA, POM or PP±0.03–0.05 mm
Selected LSR features±0.05–0.10 mm · ISO 3302-1 M1
Conditioning and measurement23 ±2 °C · 50 ±5% RH · 24 h · VMM / CMM
Agreed cosmetic color referenceD65 · ΔE ≤ 0.8–1.0 · ΔE ≤ 0.5
Gate vestige, flash and mismatch by drawing0.10–0.15 mm · 0.02–0.03 mm (TP) / 0.03–0.05 mm (LSR) · 0.02–0.03 mm

Ranges apply to selected parts and features. Agree size, resin, shrinkage and cosmetic master before FAI. DIN 16742 / ISO 20457 and ISO 3302-1 references follow the drawing and specified edition.

Molding quote and production schedule
ItemCapability and conditions
File check, standard and complex quotes2–4 h · 24 h · 48–72 h
Prototype mold, standard tool and complex T0/T110–15 business days · 3–4 weeks · 4–6 weeks
Simple and weld-add tool changes2–4 business days · 5–7 business days
T1 dispatch and pilot run after approval2–3 business days · 500–3,000 pcs / 5–10 business days
Production first lot and repeat shipments10,000–500,000+ pcs · 2–3 weeks
Trial samples and economic batch planning20–50 pcs · 100–500 pcs · 1,000–3,000+ pcs · 10,000+ pcs

Quote timing starts with complete CAD, toleranced drawings, annual volume and resin or finish requirements. Confirm mold lead time and lot size per project.

Combined-process examples and delivery stages

Rugged handheld housing

Combine a rigid PC/ABS shell, threaded inserts and a TPU grip. Review insert retention, bond and enclosure performance on assembled samples.

Busbar connector carrier

Overmold a formed copper conductor in reinforced PA. Agree locator strategy, flash limits, exposed contacts and electrical test conditions.

Flexible seal or microvalve

Start with the LSR grade, hardness and operating conditions. Verify the parting line, dimensional fixturing and functional seal on samples.

  1. DFM and route selection

    Confirm annual demand, resin, critical features and mold structure. Review gates, parting lines and release direction before tooling.

  2. Tool build and T1 trial

    Run the intended resin and identify trial samples by cavity. Record initial fill, appearance and dimensional findings.

  3. First article and process window

    Approve the drawing revision, reference samples and measurement plan. Close agreed dimensional, cosmetic and functional issues before release.

  4. Production ramp and downstream work

    Lock material lots, cavity identification and packaging. Coordinate secondary operations and repeat shipments with the approved lot inspection plan.

Frequently asked questions

When should we move from machining or printing to a mold?

Compare revision frequency, first and annual volumes, and what the prototype needs to prove. A trial tool is useful when the intended resin, knit lines, shrinkage or two-material adhesion must be tested.

How are mold ownership, storage and changes agreed?

Record ownership in the tooling agreement along with identification, maintenance, shot counts and transfer terms. Review changes against the approved drawing before modifying the tool.

Can molding, inserts and assembly share one RFQ?

Select the relevant services in the project brief and send the assembly drawing, BOM and acceptance criteria. State which inserts or purchased components you will supply.

Why do tolerances differ between nylon and ABS or PC?

Grade, reinforcement, mold flow, geometry and moisture affect part dimensions. Specify the critical fit and conditioning, then validate the target with molded parts under the agreed measuring conditions.

When should we choose LSR, TPE or TPU?

Compare hardness, compression set, operating conditions and any regulated-use requirements for the exact grade. If bonding to a rigid shell, validate adhesion and the mechanical lock on a representative part.

What drawings and information do I need to send?

Send the STEP model and a toleranced PDF showing critical and visible surfaces, plus the target resin, finish, first order and annual demand. For inserts or overmolding, provide separate bodies or drawings.

Send drawings for a coordinated molding quote

Include resin, cosmetic zones, first and annual quantities, and acceptance requirements. Ask for a route recommendation if tooling or process is still open.

Project brief

Processes to review

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.