Skip to content

Vacuum PVD, DLC and anti-fingerprint coatings

Select decorative vacuum PVD, a functional DLC system or an anti-fingerprint topcoat by substrate, visible area and use conditions. Review the whole coating stack and the measurements required after coating.

Selected stainless PVD/DLC stacks
1–4 μm
Sample color approval planning estimate
5–7 days
Batch processing planning estimate
7–12 days

Confirm scheduling after reviewing fixtures, color samples and required tests.

Vacuum coating chamber and examples of decorative and dark-coated metal parts

Decorative PVD, functional DLC, AF and wet electroplating

Compare layer thickness, contact conditions, heat input and the required evidence.

Engineering criterionDecorative PVDFunctional DLCAF topcoatWet electroplating
Layer thickness1–4 μm reference for selected stainless steel systems.1–4 μm reference for selected stainless steel systems. Account for the interlayer.Thin topcoat. Set acceptance by surface performance.Specify the required buildup and the local minimum at measurement points.
Hardness and wearReview hardness when the surface has a wear requirement.Agree an instrumented indentation method and verify adhesion independently.Evaluate the topcoat after abrasion on the specified substrate.Depends on the deposited metal, undercoat and required service.
Friction and surface behaviorStart with the approved texture, color and gloss sample.Test friction and wear with the intended counterpart, load and lubrication.Measure contact angle and cleanability on matched samples.Inspect corrosion, electrical or decorative performance as specified.
Heat and coverageCheck the substrate’s allowed temperature and shadowing in grooves.Check tempering history, allowable heat input and coverage on working faces.Check topcoat compatibility with the approved base finish and cleaning process.Review current distribution and solution access in holes and recesses.
Typical useWatch cases, clasps and decorative hardware.Sliding pins, guides and loaded contact faces.Touch surfaces on cases, controls and trim.Corrosion protection, conductive contacts or dimensional buildup as specified.

Cleaning, masking and vacuum coating routes

Cleaning, fixturing and masking

  • Remove process oils and residues. Identify forbidden rack marks, the visible Class A surface, masking boundaries and part orientation before sampling.
  • Check thread and bore masking, plug thermal compatibility and line-of-sight limits in deep features. Agree coverage on actual parts.

Coating systems and acceptance methods

Switch coating systems to see suitable substrates, how to specify the finish and what to test.

TiN / ZrN · Gold tones

Typical use
Review polished or brushed stainless steel, titanium or prepared brass. Approve gold or champagne tones on the intended substrate.
Measurement and acceptance
Specify the physical master, gloss, measuring geometry and ΔE formula. Confirm any sweat test and its scope for the part.
Measurement and acceptanceTest methodWhat to specify on the drawing or inspection plan
Film thickness and stackUse crater grinding, a suitable cross-section method, or XRF when calibrated for the stack.Reference 1–4 μm for selected stainless-steel PVD/DLC routes. Specify substrate grade, interlayer, functional film, measuring position and masking.
Film hardness and adhesionUse instrumented indentation under ISO 14577-4 as applicable. Select a separate scratch or indentation procedure for adhesion.For a hardness target such as 1200 HV, agree a film-appropriate test, load, substrate influence and the acceptance method. Agree separate adhesion and wear evidence.
Color, gloss and corrosionUse spectrophotometry and the approved sample. Define any additional sweat or corrosion test for the specific product.For a target such as ΔE ≤0.8, record the formula, illuminant, measurement geometry, orientation and points.
AF repellency and durabilityMeasure water contact angle before and after dry abrasion. Use ASTM D8380 where the surface and agreed method are applicable.Agree the control coupon, abrasive, force, cycles, contact-angle threshold and cleanability criteria before sampling.

Technical references · ISO 20523 · ISO 14577-4:2016 · ASTM D8380

Typical parts and coating checkpoints

Define coating type, acceptance sample and critical surfaces for the actual part.

Watch-band clasp or visible hardware

Approve color and gloss on an actual part. Check adjacent brushed and mirror areas, edges and agreed points for skin-contact requirements where relevant.

Sliding pin or guide

Review post-coating fit with the mating part. Validate wear, friction and film adhesion on the relevant surfaces.

Electronic controls and instrument components

Try AF on touch surfaces. For instrument parts, review the substrate and application separately and specify cleaning, sterilization or compliance validation when required.

Color measurement, AF durability and protective packing

Spectrophotometry and adhesion inspection

Record L*, a*, b* and ΔE against the master. Use a part or a representative coupon from the same run where agreed. Record the adhesion method, damage rating and lot.

Water contact angle and abrasion

Keep droplet volume, measurement timing and surface preparation consistent. If using steel wool, record the grade, load, strokes and acceptance threshold.

Scratch protection and lot packing

Handle cosmetic parts with clean gloves, separate them in a tray and qualify any protective film for residue and clean removal. Match each package to its coating lot.

From drawing review to coating lot release

  1. Drawing and service conditions

    Identify substrate, wear zones, visible faces and service conditions.

  2. Fixturing, masking and sample coating

    Confirm preparation, film stack, racking and masking.

    5–7 days · Sample color approval planning estimate

  3. Sample approval and testing

    Approve appearance and test results on parts or agreed witnesses.

  4. Production and lot release

    Retain the approved finish and inspection plan with the lot.

    7–12 days · Batch processing planning estimate

Frequently asked questions

How do PVD and DLC relate to each other?

PVD describes a deposition route. DLC describes a family of carbon films that may be deposited by PVD or an applicable CVD route. Specify the required film and performance.

Why review substrate hardness for DLC?

A hard thin film needs support under load. Check alloy, heat treatment, contact pressure and interlayer before specifying a hardness target.

How does coating affect a precision fit?

If a uniform film of thickness t coats all the way around, an outside diameter grows by approximately 2t and an inside diameter shrinks by approximately 2t. Specify masked surfaces and the final measurement state.

How should AF performance be compared?

Compare coated and reference specimens under the same material, texture, cleaning and abrasion conditions. Define how you will assess fingerprints, staining and loss of performance.

Where can rack marks appear?

They can appear at the contact or support points. Mark permitted zones on the drawing and approve a limit sample if the area remains visible.

How should a part be prepared before PVD?

Specify mirror, brushed or blasted finish on each face, remove oils and residues, and confirm the allowed witness marks and edge breaks. Evaluate the coating on the approved base texture.

Send drawings for engineering review

Send a drawing, substrate, sample or batch size and any reference color or performance request.

Engineering review brief

Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.