Skip to content

Sheet metal design and drawing guidelines

Use this guide to check bend geometry, tooling access, functional datums and finish callouts. Send a formed STEP model and a matching 2D drawing so KeepWin can review the features that control assembly.

Flat sheet metal blank and formed enclosure beside a caliper
V ≈ 6T–8TInitial V opening for air bends
≥ 2T + RHole-edge to bend-line review
STEP + 2D PDF + BOMDrawings and assembly parts list

Set bend geometry from grade, thickness and tooling

Specify nominal thickness T, material condition and grain direction. Check each bend in the forming sequence.

Inside radius and grain direction

Start with the 90° matrix for the listed grades and thicknesses. Review temper and grain for crack-sensitive bends, including 6061-T6, and validate the chosen radius with the actual tool.

Bend relief and nearby holes

Place reliefs where a bend ends next to another flange or a flat face. Dimension the nearest edge of a hole or slot from the bend line and flag any feature that must stay round.

Z offsets and flattened hems

Specify offset height, face-to-face clearance and which surfaces the step must align. For a hem, confirm material ductility, closing gap and any coating allowance with the intended method.

90° bend radius and flange starting points
ThicknessV-dieSteel / 5052 R304 / 316L R6061-T6 ROuter flange
1.0 mmV6 / V80.8–1.01.0–1.21.5–2.05.5–6.5
1.5 mmV10 / V121.2–1.51.5–1.82.5–3.07.5–9.0
2.0 mmV12 / V161.6–2.02.0–2.53.0–4.09.5–11.5
3.0 mmV20 / V242.5–3.03.0–3.54.5–6.014.5–17.5
4.0 mmV25 / V323.5–4.04.0–5.06.0–8.018.0–22.0

All bend quantities are in mm. Verify radius and flange with the actual material condition and rolling direction.

Check 90° bends and punched features before drawing release

Select a sheet grade and enter nominal thickness. Look up 90° tooling references and review nearby holes, reliefs and offsets.

Choose a grade and enter a positive thickness.

These are drawing review starting points. Hole and relief calculations use the upper radius from the matrix. Confirm the actual bend angle, grain, tool, measurement origin and feature geometry before release.

For a 90° corner, the starting layout uses width T and depth T + R. Check where the relief extends relative to the bend zone.

Plan local forms, hardware and tool clearance

Punched holes, countersinks and local forms

Specify hole shape and burr side. For louvers, ribs, embosses or extruded tapping holes, give the height, direction and clearance to nearby bends or fasteners.

Access for clinched, riveted and welded hardware

List the exact part number and installation side. Verify sheet hardness and thickness, mounting hole, edge distance and access for both the tool and support.

Deep channels and return flanges

Review each bend with the walls already formed. Check gooseneck or segmented tooling for clearance and leave a way to remove the part from the tooling.

Stock countersink angles · 82° / 90° / 100°

Check the smallest hole or slot against the selected punching tool or laser process. Evaluate hole pitch, edge distance and burr direction.

Mark functional requirements on the 2D drawing

Distinguish same-face hole dimensions from dimensions that span bends. Specify where each requirement is measured on the finished part.

Functional datums and measurement state

Define the mounting datums and critical fits. State whether the dimensions apply in free, supported or assembled condition and identify the matching part when needed.

Visible faces, coating and masked zones

Mark visible faces, brushed direction and acceptable tool marks. Identify masked threads, grounding pads and locating faces and specify where coating thickness affects the fit.

Weld extent and seam finish

Specify weld type, location, length and any grinding or blending. Where a joint must seal, state the required test and acceptance conditions.

Drawing package checklist

ItemWhat to specify
Model, drawing and flat patternUse matching revisions and units for the formed STEP and 2D PDF. Identify which file controls manufacturing and whether the flat pattern is for reference.
Material and nominal thicknessWrite the exact grade and condition, for example 5052-H32, T = 2.0 mm. State any grain, polish and certificate requirements.
General tolerances and critical fitsIdentify the applicable standard, edition and scope. Add individual tolerances and functional datums where assembly or performance requires them.
Hardware list and masking drawingIdentify the exact hardware number, quantity and side in the BOM. Show mask boundaries and confirm the condition for inspection after finishing.

Confirmed forming and punching references

Check material and thickness before using the equipment, tolerance or form references.

Press brake envelope and drawing limits
ItemCapability and conditions
Standard and tandem length, force3,100–4,200 mm · 6,000 mm · 36–320 tf
Bend angle, single and cumulative dimensions±0.3–0.5° · ±0.10–0.15 mm · ±0.20–0.30 mm
Initial V-die, hole-to-bend and offset reviewV ≈ 6T–8T · ≥ 2T + R · ≥ 2.5T–3T
Deep channels and interferenceReview gooseneck or sectional tools for deep boxes. Check opening and depth in the bend sequence.
CNC turret punching and forming tools
ItemCapability and conditions
Carbon steel/aluminum and stainless steel thickness0.5–4.0 mm · 0.5–3.0 mm
Round holes and countersink toolsØ1.0–88.9 mm · 82° / 90° / 100°
Common tools and shapesSquare and oblong holes, louvers, embosses, ribs, extruded tapping holes, dimples, knockouts and lances.

Choose a sheet grade for the drawing

Use the 90° and punching rows below to narrow the options, then confirm supply condition and tooling for the selected grade.

Aluminum alloys

Temper and rolling direction affect cracking risk and radius. Specify the required finish and alloy.

5052-H32 · 6061-T6 · 1060-H24 · 3003 · 7075

0.5–10.0 mm

Carbon steel

Record the exact grade, thickness and protection required at cut edges.

SPCC · DC01 · Q235B · SPHC · 65Mn

0.5–16.0 mm

Galvanized steel

Specify coating designation and protected areas after cutting, forming and joining.

SECC · SGCC · DX51D

0.5–16.0 mm

304 / 304L stainless steel

State the exact grade, visible finish and acceptable tool marks.

304 / 1.4301 · 304L

304 · 0.4–12.0 mm

316 stainless steel

Confirm grade, finish and corrosion requirements for the finished part.

316 / 1.4401

0.5–10.0 mm

316L stainless steel

Call out the low-carbon grade and the finish required in weld areas.

316L / 1.4404

0.5–8.0 mm

Copper and brass

Check sheet temper, forming direction and functional contact faces.

T2 · C11000 · H62 · H65 · C5191

0.2–6.0 mm

Titanium sheet

Confirm the grade and supply condition. Review bend radius, springback and joints for the actual part.

Grade 2 · Grade 5 (Ti-6Al-4V)

Confirm from the drawing

Compare sheet material families

Choose at least two families for the comparison.

Verify drawing datums and surface references

Measure the feature in the specified setup

Agree how the part is located and supported. Use a fixture, gauge or CMM to record the specified datum-based dimensions in that condition.

Agree appearance with reference samples

Approve color, texture, sheen and grain direction under the agreed viewing conditions. Identify the retained sample by revision and finish in the order.

From drawing submission to first-article approval

  1. Submit the formed model and controlled drawing

    Include the part revision, nominal thickness, quantity and the assembly BOM where applicable.

  2. Check geometry and tool access

    Review crack risk, bend relief, hole placement, hardware access and clashes in the forming sequence.

  3. Confirm the flat pattern and inspection plan

    Agree bend compensation, finish boundaries, critical dimensions and the measurement state before quoting the approved scope.

  4. Validate the first part and retain the setup

    Record sample approval, drawing revision and the agreed tools and gauges for later orders.

Send drawings for a manufacturability review

Upload the formed STEP and 2D PDF with the features you want reviewed. Draft drawings are welcome. Arrange transfer of native DXF or editable BOM files during engineering review.

Sheet metal design review brief

Review topics

Attach the geometry check or material comparison, or choose drawing status and review topics.

Contact and CAD files

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    FAQs

    How should I choose the inside bend radius?

    Start from the grade, temper, thickness and grain direction. Use the published 90° matrix for the listed combinations and verify the actual tool and bend sequence.

    What should accompany a flat DXF?

    Include a matching formed STEP and a 2D PDF showing bends, functional tolerances and finish. Mark the controlling revision and include the hardware BOM for assemblies.

    Should I use the tightest tolerance everywhere?

    No. Specify what function requires and agree a practical measurement method. Unnecessary tight limits can add cost without improving the assembly.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.