Skip to content

CNC turret punching

Punch repeated holes and slots, or form louvers, embosses and knockouts in the same panel. KeepWin reviews your drawing for tool fit, burr direction and any laser cutting, leveling or bending needed for assembly.

Turret punch above a sheet metal panel with punched slots
1,500+Stock tools
Ø1.0–88.9 mmRound-hole tool range
5–8 business daysCustom tool fabrication

Single-hit punching, nibbling and burr direction

Punched holes and slots beside a sample of a curved edge

Single-hit punching

A matching punch and die shear the hole in one stroke. Check the hole size and tool clearance against the sheet grade and thickness, then specify the burr side where the part contacts a cable or mating surface.

Nibbling and laser contours

Overlapping strikes trace a curve and can leave scallops. For visible edges or critical fits, review edge finishing or laser-cut the profile, then punch features that need a forming tool.

Design review for punching and forming

Select a topic to see what to mark on the drawing.

Local forming

For louvers, embosses, ribs, half-shears, knockouts and extruded holes for tapping, show the forming direction and profile height. Mark clearance to bends and hardware, thread engagement where applicable and surfaces that must remain clear after assembly.

Sheet metal sample with louvers, embosses and other local forms

Server and cabinet panel examples

304 stainless server vent panel

For a No. 4 brushed 304 panel, review the grain direction and pitch before punching the array. Check flatness and burrs before bending, then verify the mounting-hole pattern against the chassis.

SPCC cabinet side panel

Review louver direction for airflow, knockout size for cable entry and fastener locations relative to the bends. Verify fit after forming, bending and any specified coating.

Turret punching capabilities

Check sheet size, thickness and the tool library. Confirm tolerances for critical holes, form heights and repositioned features during drawing review.

CNC turret punching and forming tools
ItemCapability and conditions
Standard and repositioned sheet size2,500 × 1,250 mm · 3,000 × 1,500 mm
Carbon steel/aluminum and stainless steel thickness0.5–4.0 mm · 0.5–3.0 mm
Round holes and countersink toolsØ1.0–88.9 mm · 82° / 90° / 100°
Common tools and shapesSquare and oblong holes, louvers, embosses, ribs, extruded tapping holes, dimples, knockouts and lances.
Library and custom tools1,500+ · 5–8 business days

Compare punching, laser and combined routes

Choose the main feature, material, thickness and order quantity. The result gives your engineer a route to evaluate when quoting.

Complete the four fields to see which route to review.

Sheet materials for punching

Compare available grades and verified punching ranges. Check the grade, stock, finish and tooling for the intended feature on the drawing.

Aluminum alloys

Verify alloy temper, ligament width and the risk of tool marks on exposed faces.

5052-H32 · 6061-T6 · 1060-H24 · 3003 · 7075

0.5–4.0 mm

Carbon steel

Confirm clearance, burr direction and coating requirements for the cut edge.

SPCC · DC01 · Q235B · SPHC

0.5–4.0 mm

Galvanized steel

Review the zinc coating and tool contact around punched edges and forms.

SECC · SGCC · DX51D

Confirm from the drawing

304 / 304L stainless steel

Specify the visible face, brushed grain direction and allowable flatness after punching or bending.

304 / 1.4301 · 304L

304 · 0.5–3.0 mm

316 stainless steel

Check the hole pattern, tool fit and any passivation called for on the drawing.

316 / 1.4401

0.5–3.0 mm

316L stainless steel

Confirm the low-carbon grade when specified and review features near welded joints.

316L / 1.4404

0.5–3.0 mm

Copper and brass

Review grade, temper and handling of contact or cosmetic surfaces.

T2 · C11000 · H62 · H65

Confirm from the drawing

Titanium sheet

Review the titanium grade, condition, thickness and feature before quoting the route.

Grade 2 · Grade 5 (Ti-6Al-4V)

Confirm from the drawing

Compare sheet material families

Choose at least two families for the comparison.

Inspect hole geometry, burrs and form height

Before releasing the first article, agree which datums govern hole locations, how height and direction are checked on formed features, and which edges need deburring. For dense patterns, specify the flatness area and inspection stage.

Request a first-article report or a fit check if these are needed for acceptance. Identify the dimensions to include when sending the drawing.

Measuring a bent sheet metal bracket with a caliper

From tool matching to protected shipment

  1. Match the drawing and tool

    Review grade, thickness, key fits and stock tools. Quote custom tooling separately when needed.

  2. Punch, form and check the first part

    Sequence holes and forms around the bends and clamps. Confirm burr side, local forms and any leveling requirement.

  3. Finish, bend and check fit

    Follow the approved order for edge finishing, bends, hardware and coating. Check the critical dimensions in the agreed condition.

  4. Protect and identify the batch

    Separate visible faces and protect raised features. Record the approved drawing revision and tool for repeat orders.

Finished sheet metal parts staged for packing with protective dividers

Send drawings for a punching quote

Include the required quantity, critical hole dimensions, visible face and direction of formed features. Tell us which dimensions can be adjusted to fit stock tools.

Punching project brief

Operations and tooling options

Select any required operations or attach a route estimate or material comparison to build the brief.

Contact and CAD files

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    FAQs

    Can a louvre be made with a hole punch alone?

    A raised louvre requires suitable forming tooling and geometry, not merely a through-hole operation.

    How do you check dense perforated panels for warping?

    Define the flatness tolerance, inspection area and assembly condition. We review the hole pattern and leveling needs before inspecting representative parts against the agreed requirement.

    Which face should I mark for burrs?

    Mark the visible face, cable entry and contacting faces, then identify where exit-side burrs are acceptable. Call out an edge break or deburring on surfaces that need it.

    Are all punched outlines perfectly smooth?

    No. Edge condition depends on tooling and route; nibbling can leave stroke marks. Specify the acceptable edge and any cleanup.

    What do I send for a part that also needs bending?

    Send the finished STEP model and the toleranced drawing. If a flat pattern is available, indicate whether it controls manufacturing. The team can confirm how to provide the native DXF or DWG during review.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.