Skip to content

Precision polishing and grinding

Plan mirror polishing, directional brushing or precision grinding around visible faces, functional geometry and the required inspection. Specify the finish by zone on watch hardware, cosmetic parts or precision mating surfaces.

Selected brushed sheet finishes
Ra 0.4–0.8 μm
Selected plated CNC fits for review
±0.005 mm
Physical sample planning estimate
3–5 days

Confirm the schedule after incoming parts, sample scope and inspection requirements are reviewed.

Polished watch links, a ground stepped block and a cylindrical pin on a granite surface

Choosing between polishing, brushing, grinding and mass finishing

Match the finish to the surface zone, required edge condition and final dimensions.

Engineering criterion8K mirror polishHL / No.4 directional brushingPrecision surface or cylindrical grindingMagnetic or vibratory mass finishing
Texture and roughnessApprove a mirror sample. Specify any Ra limit separately.Selected brushed sheet finishes can reference Ra 0.4–0.8 μm.Specify the functional Ra and lay of the ground face.A media trial establishes the texture on accessible surfaces.
Dimensions and geometryLeave enough stock to remove tool marks. Review edge rounding.Check how the process affects fitting faces and cosmetic transitions.Review final size, flatness, roundness and parallelism by feature.Check edge break, critical small holes and media retention.
Edges and boundariesUse masking and fixtures where a crisp visual boundary is required.Match grain direction and limit cross-grain scratches.Mark any acute edges, reliefs and burr limits on the drawing.Review radiusing on exposed edges and protect critical fits first.
Typical useWatch bezels, center links and decorative clasps.Outer watch links, panels and metal housings.Die inserts, precision bushings and locating pins.Exposed burrs on small CNC and MIM parts.

Finishing routes and design review

Mirror polishing and zoned finishes

  • Mark center links, side links or all faces. Use the physical sample to record contrast, allowed marks, edge retention and the boundary between mirror and brushed areas.
  • Review the incoming tool marks, masking boundary and allowable edge rounding. For an Ra target such as ≤0.025 μm, agree instrument, location and trial method.

Surface grades and precision grinding acceptance

Switch grades to see what to put on the drawing and how to verify it on the first article.

8K mirror polish

Typical use
Use 8K as an appearance designation with a physical reference. Call out center links, outer links and boundary edges separately on the drawing.
Inspection priority
Approve gloss, reflection and visual defects under agreed conditions. Measure Ra or Rz separately when the drawing specifies it.
Inspection priorityTest methodWhat to specify on the drawing
Profile roughnessUse ISO 21920-2 for profile parameters and ISO 21920-3 for specification operators. Agree direction, filter, evaluation length and locations.For the drawing, assign Ra or Rz by zone. For selected brushed sheet, Ra 0.4–0.8 μm is an initial reference.
Finished size and geometrical tolerancesUse a gauge or measurement plan suited to the size and geometry. Specify form and orientation using ISO 1101 as applicable.For selected plated CNC fits, review ±0.005 mm finish grinding against allowance, length and the finished inspection datum.
Cosmetic face approvalCompare with a signed sample under the agreed light, distance and viewing angle. Inspect grain, transition, gloss and marks.Identify the approved sample and revision. Mark the inspection zones and any protected boundary lines.
Coating remaining after grindingSelect a thickness method calibrated for the actual coating and substrate, and verify the final size.State grinding stock, the minimum residual thickness, the points to measure and limits on substrate exposure.

Technical references · ISO 21920-2 · ISO 21920-3 · ISO 1101

Typical parts and inspection checkpoints

Use these examples to identify functional and cosmetic areas on your drawing.

Metal watch bracelet links

Choose mirror on the center links and brushed sides, or specify the complete finish layout. Confirm consistent transition, pin-hole fit and edges after polishing.

Ground mold insert or mating face

Specify datum seating and inspect flatness and parallelism across the working face. Set aside the reference face for verification after heat treatment or coating.

Plated bushings and precision ground pins

Review grinding by diameter and part geometry, including centerless grinding where suitable. Check final outside size, roundness and coating retained at the working surface.

Profile roughness, flatness, and scratch protection

Contact profile measurement

Record the Ra or Rz parameter, stylus and evaluation settings. Agree measurement positions and traverse direction for each surface zone; review accessible length on small parts.

Optical flat and visual comparison

Use an optical flat with suitable illumination on surfaces that support interference measurement. Separately inspect finishes against the approved physical sample under the agreed light.

Protective film and compartment trays

Check film compatibility, removal and residue on the actual finish. Separate polished faces from each other and label packs by batch.

From drawing review to lot release

  1. Drawing and incoming part review

    Identify visible zones, mating surfaces and the supplied condition.

  2. Fixtures, masking and sample finishing

    Confirm stock, grain, edge treatment and the order of operations.

    3–5 days · Physical sample planning estimate

  3. First article and finish approval

    Approve a physical sample and measure the critical features.

  4. Lot release and protected delivery

    Inspect the finished lot and protect polished faces in packing.

    5–10 days · Batch finishing planning estimate

Frequently asked questions

Is a mirror sample enough to specify a precision fit?

Use the sample for appearance. State the datum, size, form tolerance and measuring conditions for the functional fit on the drawing.

How should mirror and brushed surfaces be marked?

Mark each zone, grain direction, a transition line and any protected edge on the drawing or model. Use a signed physical sample to agree the allowed boundary.

What can mass finishing change on a small hole?

It can round entrances, alter accessible surfaces and leave trapped media. Check the trial parts and consider finishing critical holes afterward.

Can polishing be combined with coating?

Yes. Confirm whether the surface is polished before coating or ground after plating. Agree the final thickness, gloss and dimensions for the selected sequence.

How much stock is needed for grinding after plating?

Work backward from the finished size and minimum retained coating. Include plating variation and grinding setup, and state whether the allowance is radial or diametric.

How does the incoming surface affect polishing cost?

Deep tool marks or pits may require extra stock removal and inspection. Share the incoming part condition and a sample so the route can be planned.

Send drawings for engineering review

Send the drawing and a sample or reference photo, and specify finish zones, key dimensions and batch size.

Engineering review brief

Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.