Skip to content

Dedicated cutting and production drilling

For cut-to-length profiles and repeat hole patterns, compare dedicated fixtures, automatic feeding, and general CNC. Define drilling, reaming, countersinks and threads from the drawing and match the route to lot size and part revision.

H7 diameter on drawings
Ø10 H7
Geometry and position callouts
ISO 1101
Reference for fixture trial
2–4 days

Confirm the fixture, incoming stock, operations and inspection scope before scheduling.

Multi-station drilling cell machining metal workpieces in a dedicated fixture

Dedicated drilling, general CNC and sheet-hole cutting

Compare annual demand, releases per year, machining steps and drawing revisions before committing to tooling.

Engineering criterionDedicated multi-station drillingGeneral CNC machiningSheet laser or punching
Order profileStable part family, repeat releases and consistent stock.New designs, frequent revisions, mixed parts or low volume.Flat sheet with accessible through-holes and repeated patterns.
Hole featuresUse qualified sequences for repeated drills, reams, recesses or threads.Assess angled bores, multiple faces and features needing milling or thread milling.Cut or punch the through-profile. Add machining for blind bores, precision fits or threads.
Cost and setup driversCompare fixture investment, changeover and tool life with the verified cycle time.Account for programming, workholding and the number of setups.Cost depends on sheet yield, cut path or punch tooling and any follow-up work.
Acceptance focusVerify locator repeatability, tool-change drift, and the equivalent output across stations.Verify datum transfer, tool access and relationships across faces.Check hole profile, burrs, edge deformation or taper as applicable.

Four routes for cut-to-length and hole machining

Cut to length and establish the datum

  • Record the stock grade and condition, such as 6063-T5 for extruded profiles, 6061-T6 for extrusions or plate, and 304 or 316 for stainless stock. Check the incoming section, straightness and end condition.
  • On hollow stock, agree clamping pressure and access to burrs inside the section. Identify the cut face used for downstream location.

Hole features and drawing acceptance

Choose a hole feature to see what to specify and how to verify it. The dimensions shown are drawing examples. Production limits are confirmed from material, geometry and trial parts.

Through and blind drilling

Typical use
State diameter, effective depth, through or blind condition, and the hole pattern. For deep holes provide the depth-to-diameter ratio and the exit wall or available clearance.
Inspection item
Review chip removal, tool reach and exit burrs. Select separate checks for diameter, depth and position.
Inspection itemTest methodDrawing and acceptance requirements
Incoming section and cut lengthMeasure from the drawing datum. Agree length tolerance, squareness and deburring limits.For example, 420 ±0.15 mm from the marked end face. State whether downstream machining uses the sawn or finished face.
Hole size, location and depthUse a size gauge or bore instrument for diameter. Use CMM or an agreed functional gauge for the pattern and datum relationships.Example position callout: ⌀0.05 mm to A | B | C under ISO 1101 with the datum system defined. Use the drawing’s size and position requirements independently.
Threads, burrs and recessesVerify the internal thread with suitable plugs, the recess with depth or profile measurement, and the exit edge by the approved burr criterion.Separate the drill depth from full thread depth. Specify surface treatment and the condition for final gauging.
First, last and changeover checksIdentify sampling and checks after tool, fixture or datum changes. Compare readings against the approved first piece.Record lot, station and drawing revision. Specify the treatment of suspect parts since the last accepted check.

Technical references · ISO 286-2:2010 · ISO 1101:2017 · ISO 5459:2024 · ISO 965-2:2024 · ISO 1502:1996

Three parts and their inspection priorities

Match the locating scheme and bore checks to the actual assembly interfaces.

Cut and drilled extrusion blocks

Set cut length from the datum end and check hole pitch after seating against the fixture stop.

Bracket with holes on two faces

Agree the flipping datum and check alignment between the two faces on a first article.

Repeated fixture or mounting plates

Compare drill, ream and thread sequence. Verify the mating pattern and mark tool replacement checkpoints.

Pin and thread gauges, CMM and shipment protection

Hole size and thread gauging

Use limit plugs or bore instruments matched to the finished hole. For metric threads, agree the specified class and the ISO 1502 gauging method. Record the tool and inspection stage.

CMM checks for hole patterns

Build the CMM alignment from the drawing’s datums. At first-article and agreed rechecks, record each required pattern or opposite-face relationship and tie results to the drawing revision.

Burr removal and lot protection

Clear chips from blind holes and hollow sections. Check accessible exits for burrs, then use dividers or agreed thread protectors. Preserve lot identification with the inspection record.

From drawing review to lot release

  1. Drawing, datums and order volume

    Review stock, datum and order pattern.

  2. Fixture preparation and process trial

    Trial feeding, workholding and tool sequence.

    2–4 days · Reference for fixture trial

  3. First article and gauge approval

    Approve first-piece cut, hole positions and gauging.

  4. Production checks and shipment

    Complete lot checks and protect finished threads and faces.

    5–10 days per lot · Reference solely for planned repeat lots

Frequently asked questions

When is a dedicated fixture worthwhile?

Compare annual demand, release size, changeover and tooling life. Dedicated tooling suits stable repeat geometry after first-article approval.

Can hole position be held after flipping?

Specify a repeatable datum and locator scheme. Measure both faces and their relative positions after flipping on a first article.

Can drilling and tapping run in one sequence?

Review access, chip evacuation, thread depth and tool-break detection. Approve the sequence and verify finished threads separately.

What should I specify for deep drilling?

Provide diameter, usable depth, material, entry geometry and required straightness. Review guidance, tool reach, coolant and chip evacuation. Confirm any specialized deep-drilling route on the part geometry.

How much extra drill depth does a blind thread need?

Start with required full thread depth. Add the selected tool’s lead, runout and clearance for its chip behavior, accounting for the drill-point shape and remaining wall. Confirm available depth before tooling.

How will anodizing affect finished threads?

Agree coating type, thickness and masking on the drawing. Qualify any machining allowance or masking on a sample before production. Final gauging follows the specified surface condition.

Send drawings for engineering review

Send a drawing or hole table with the stock form and grade, per-lot quantity, annual demand and final inspection requirements.

Engineering review brief

Select the route, feature and stock form. Add the alloy, critical dimensions and repeat demand to pass them to the quotation form.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.