Skip to content

Liquid spray painting and bake curing

Choose a liquid paint system for metal enclosures, panels and cosmetic parts. Match the pretreatment, color sample and cure schedule to the substrate, fitted components and service conditions.

Dry film reference for selected sheet-metal systems
35–65 μm
Example color criterion subject to the agreed method
ΔE ≤0.8
Physical color sample planning estimate
3–5 days

Confirm the project schedule after the paint system, color sample, masking and tests are agreed.

Operator spray painting a masked enclosure in a coating booth

Liquid paint, powder coating, anodizing and e-coating

Compare the coating stack, final appearance, thermal budget and how each part is masked.

Engineering criterionLiquid spray paintingPowder coatingAnodizingE-coating
Film and substratePrimer and topcoat or an approved single-coat system. Specify total dry-film thickness.Cured powder film. Review buildup around edges, threads and mating areas.An oxide layer grown on suitable aluminum alloys. Account for dimensional change where required.Paint deposited from a bath on suitable conductive parts. Review contacts and how cavities drain.
Appearance and matchingUse actual color, gloss and texture samples for appearance acceptance.Verify the specified texture and gloss against a cured powder sample.Alloy and preparation affect the metallic tone. Match mixed alloys on actual parts.Confirm the finish as a stand-alone layer or primer under the specified topcoat.
Temperature and cureUse the selected paint’s technical data to confirm flash-off, part temperature and hold time.Check powder cure by actual part temperature and the selected powder specification.Review bath conditions and sealing. Confirm compatibility of any inserts or preassembled parts.Check post-bake cure and the thermal limits of any fitted components.
Masking and production fitPlan plugs, tape and rack points around the visible and functional zones.Verify mask edges and color-change setup before fixing the lot plan.Allocate rack marks and mask critical contacts or fits as required.Plan hanging, contact, drainage and coverage for the actual assembly geometry.

Coating routes and DFM review

Cleaning, pretreatment and masking

  • Inspect incoming oil, weld residue, scratches and corrosion. Agree cleaning and preparation by substrate, rack-contact marks and masking for threads, grounding and mating faces.
  • Mark the intended paint boundary and allowed creep. Inspect the finished masked surface with a thread gauge, a mating part or the specified electrical test as appropriate.

Liquid paint systems and acceptance criteria

Switch systems to see what to confirm at sampling and what to measure on the actual part.

2K polyurethane topcoat

Typical use
Review an appearance-grade finish for the substrate. Confirm mix ratio, pot life, pretreatment and any primer requirement from the product data.
What to verify
Sign the physical sample. Record color, gloss and total dry film at agreed points after cure.
What to verifyTest methodDrawing and acceptance requirements
Dry-film thicknessUse ISO 2808 where applicable. Choose a calibrated method for the substrate, such as magnetic induction on ferromagnetic steel or eddy current on suitable nonferrous metal.For applicable sheet-metal liquid paint, use 35–65 μm total dry film as a review reference. Define the required points on flat, edge or recessed areas.
Color, gloss and visual limitsCompare visually with the master under agreed light such as D65. For gloss, select the geometry under ISO 2813 as applicable.For a criterion such as ΔE ≤0.8, agree the formula, illuminant, measuring geometry, sample and points. Define gloss angle and acceptable orange peel, dust or runs separately.
Cross-cut or adhesion verificationUse the specified ISO 2409 or ASTM D3359 method where applicable. Record cut spacing, film thickness, cure state and the individual rating.Define a limit in the named method, such as ISO 2409 class 0 or ASTM D3359 Method B grade 5B when specified. Agree a separate pull-off test if needed.
Cure and functional interfacesCompare recorded part temperature and dwell with the paint data. After demasking, verify threads, the specified contacts and mating clearance.Set contact resistance or continuity limits and the test points when required. Agree cure state before handling and packaging.

Technical references · ISO 2808:2019 · ISO 2813:2014 · ISO 3668:2017 · ISO 2409:2020 · ASTM D3359-23

Three parts, three paint decisions

Use the examples to identify what your drawing and approved sample need to define.

Painted sheet-metal enclosure

Mask threads and electrical grounds. Check measured film and appearance on exterior faces and around openings.

Color-matched panel and cover

Approve an assembled pair on actual substrates under the agreed light. Check gloss and color across the seam.

Hardware with heat-sensitive inserts

Confirm the insert and seal temperature limits. Review pre-coating or an approved alternative cure and verify the final fit.

Inspection points and shipment protection

Dry-film thickness and gloss

Identify the substrate and suitable gauge. Agree gloss angle and flat measurement points, and use a representative witness coupon when edges or curves prevent reliable readings.

Appearance and adhesion

Compare visible faces with the signed sample under the agreed lighting. For cross-cut testing, agree the method and rating, and use an approved area or witness coupon.

Separation and packaging after cure

Pack fully cured parts in separated trays or EPE slots. Qualify any low-tack protective film on a sample to check for adhesive transfer and gloss change.

From paint specification to batch release

  1. Review drawings and finish requirements

    Agree substrate, finish reference and service environment.

  2. Validate masking and prepare a sample

    Trial preparation, rack points, masking and cure.

    3–5 days · Physical color sample planning estimate

  3. Approve the sample and inspection plan

    Approve the part and its measurement plan.

  4. Inspect and protect the batch

    Inspect the lot and protect cured surfaces for packing.

    5–8 days · Batch coating planning estimate

Frequently asked questions

What is the difference from powder coating?

Compare finish sample, dry-film limits, part geometry and temperature budget. Validate the selected coating and cure on the actual part.

Can an RAL number alone define acceptance?

Use the code to identify the target. Approve a physical sample on the actual substrate and agree gloss, texture and any instrumental limits.

How are masked areas accepted?

Define boundary, allowed paint creep and checks on threads or ground contacts. Release the coating and masked areas together on a trial part.

Does laser marking go before or after painting?

Compare both sequences on the actual substrate and paint system. Approve the contrast, mark position and required durability. Check any exposed substrate against the corrosion requirements.

Can the enclosure be painted and still have grounded interfaces?

Mark the coating boundaries, ground points and mating faces on the drawing. Review the coating sequence and contact continuity. If enclosure shielding is required, agree a separate test in the specified assembly state and frequency band.

How are heat-sensitive inserts and seals handled?

Provide the component limits for part temperature and dwell time. Review whether to paint before assembly or qualify a lower-temperature cure on a representative sample.

Send drawings for engineering review

Send the drawing and finish specification or master-sample reference. Include visible faces, coating windows, temperatures, quantities and any specific tests.

Engineering review brief

Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.