Evaluate wire EDM for through-profiles in conductive materials, including die inserts, precision fixtures and metal AM build release. Plan wire access and measure the cut in its final state.
Wire diameter options for review
Ø0.10–0.25 mm
Example profile target for trial validation
±0.002–±0.005 mm
Prototype scheduling estimate
3–5 days
Confirm tolerances and timing after geometry, thickness, setup and inspection are reviewed.
Wire EDM guide above a clamped metal workpiece with cut samples nearby
Wire EDM, CNC milling, sinker EDM and laser cutting
Compare material, tool access, final geometry and the condition of the cut surface.
Engineering criterion
Wire EDM
CNC milling
Sinker EDM
Laser cutting
Materials and supply state
Conductive stock, including selected hardened steels and carbides.
Review cutting tools, hardness, tool reach and fixturing.
Conductive workpiece. Confirm shaped electrode material and wear.
Sheet grade, thickness and assist gas determine the route.
Feature access
Through profiles. Closed profiles need a threading path.
Accessible pockets, steps and 3D surfaces. Internal corners depend on tool radius.
Blind pockets and deep cavity features reachable by an electrode.
Through-cut sheet contours. Review cut width and access.
Dimensional acceptance
Set profile, internal radius, taper and sections through the thickness.
Specify datums, cutter access, any handoff between setups and tool marks.
Check electrode wear, internal corners and cavity depth.
Check kerf taper, dimensional drift and cut-edge quality.
Surface effects
No conventional cutting force. Residual stress can still move parts; verify recast as required.
Check clamping, vibration and tool marks on thin features.
Verify the EDM surface and affected layer on the functional face.
Check heat-affected edges, dross and post-cut cleanup when required.
Wire EDM routes and DFM review
External profile cutting
Plan the entry from an edge. Agree holding points, allowance for subsequent operations and how the cut part will be supported when released.
Plan temporary tabs, fixtures or core capture before the final pass. Keep the datum accessible for reinspection.
Closed through-profile cutting
Place a usable start hole in the discard area. Review wire diameter and spark gap against the internal radius, thickness, flushing and whether a taper is required.
Place the starter hole in scrap with room for threading and entry. On tapered work, state the top and bottom profiles or angle and reference height.
Rough cut and multi-pass skim cutting
Rough cut to an allowance, then use lower-energy skims when the profile or finish requires it. Confirm pass count by material, height and flushing access.
Measure the first article at multiple heights where needed. For a target such as Ra ≤0.2 μm, agree the test direction and verify it on the actual cut.
Metal additive build-plate part-off
Agree the separation plane, support stock and datum handoff. Verify the build plate seating and a safe sequence to release each part.
Review stress relief before removal for the alloy and build route. Inspect deformation after release and leave the agreed stock for finishing.
Electrode wire options and acceptance criteria
Use these wire sizes and cutting modes as review options. Confirm final limits for the actual stock thickness, workpiece and setup.
Ø0.25 mm standard wire
Typical use
Review for robust through-profile cutting when the shape has room for the wire and discharge gap.
Inspection priority
The nominal wire radius is 0.125 mm before the discharge gap. Confirm flushing, starting access and actual inside radius.
Ø0.20 mm multi-pass option
Typical use
Evaluate a narrower kerf or multi-pass surface control while retaining suitable stiffness and flushing.
Inspection priority
The wire radius is 0.10 mm before the gap. Inspect the profile and taper across the thickness after the agreed passes.
Ø0.10 mm fine wire
Typical use
Evaluate slots or close corners where finer wire and stable threading can be supported.
Inspection priority
The wire radius is 0.05 mm before the gap. The finished radius also depends on discharge conditions, height and taper. Confirm it on a trial.
Taper cutting
Typical use
Use for tapered through profiles. Provide the direction, reference plane, stock height and upper and lower profiles.
Inspection priority
Confirm wire-guide clearance, flushing and available angle at the actual height. Inspect both faces and any agreed intermediate section.
Inspection priority
Test method
Drawing and acceptance requirements
Material and access
Confirm stock condition, stable conductivity and the available threading path before programming.
Use electrically conductive stock. Provide alloy, hardness, stock thickness and through-cuts versus cavities. Review alternate routes for blind cavities.
Profile and geometry
Use optical contour measurement or another suitable method by datum and section. Check upper and lower profiles when the cut is tapered.
State the finished profile tolerance, datum, maximum inside corner radius and any taper. Agree the sections to measure across the part thickness.
Surface state and inspection
Use ISO 21920-2 for profile parameters and ISO 21920-3 for evaluation settings. Use a polished cross-section for the recast layer where required.
Agree Ra and measuring direction under the drawing standard. Where fatigue, sealing or subsequent coating matters, specify how to assess the altered surface layer.
Metal build-plate separation
Compare pre-cut references and released dimensions. Check residual support stock at the final machining datum.
Specify separation plane, offset, heat-treatment sequence and the dimensions to recheck after release.
Use these examples to identify section heights, critical profiles and release checks.
Hardened mold insert
Review closed through-profile, start-hole position and internal corner radius. Verify profile and taper across the cut thickness.
Metal AM build plate release
Agree the separation plane, pre-cut heat treatment if specified, and machining stock for final datums. Check the part after release.
Fine slots, collets and miniature gears
Review the kerf, small radii and thin webs. Check slot width and tooth profile by datum; measure elastic parts in the agreed free or clamped state.
Optical profiling, recast inspection and corrosion protection
Optical contour measurement
Define lighting, edge detection, access and the measured face. Add a suitable method for intermediate sections when the top and bottom faces cannot establish the profile.
Roughness and metallographic recast inspection
Measure the profile on the cut face. For fatigue or sealing requirements, agree coupon representativeness, cross-section locations and how to report recast thickness.
Drying, corrosion protection and packing
Remove residual dielectric fluid and dry promptly. Agree compatible corrosion protection, such as VCI packaging for appropriate ferrous parts, and isolate cut faces.
From drawing review to lot release
Drawing and conductivity review
Check geometry, alloy, hardness and stock thickness.
Threading, workholding and passes
Agree wire entry, fixturing, cutting sequence and measurement.
Wire cutting and first article
Verify specified profiles, tapers and surface condition.
2–4 days · Cutting and first-article planning estimate
Cleaning and lot release
Record release condition and protect the cut face in packing.
Frequently asked questions
Can a wire cut an enclosed blind pocket?
Wire EDM needs a through-path for the wire. For a blind cavity, review sinker EDM or a milling route that can reach the feature.
What sets the smallest internal corner radius?
Review wire diameter plus the discharge gap, then check part thickness, taper and the required finish. Verify any critical corner on a trial part.
Can hardened tool steel and carbide be wire-cut?
Review the exact alloy or carbide grade and its conductivity. On heat-treated parts, confirm stock thickness, residual stress, workholding and surface acceptance before cutting.
Should metal printed parts be stress-relieved before separation?
Agree the sequence with the build supplier. It depends on the alloy, build route, support design and drawing. Document the state at cutting and the checks after release.
How is water-related corrosion on tool steel controlled?
Review the allowed immersion time, water condition and the drying and protection plan for the grade. Confirm any cleaning or no-oil requirement before shipment.
What is the EDM recast layer?
It forms when molten material resolidifies on the cut surface. Lower-energy skim passes can reduce it. Agree the allowable layer and verify it by cross-section when functional performance depends on it.
Send drawings for engineering review
Share the drawing, material and thickness, plus the starter hole, required radius, taper and surface acceptance.
Engineering review brief
Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.