Skip to content

Metal injection molding (MIM)

For repeat production of small metal parts with complex shapes, review stainless steel or titanium feedstock, sintering shrinkage and critical post-machining features with the drawing.

As-sintered tolerance for initial review
±0.3%–±0.5%
Wall thickness for initial review
0.5–6.0 mm
Tooling and T1 planning estimate
25–35 days

Confirm by drawing and trial samples. Timing starts after tooling release and schedule confirmation.

Molded green parts, a ceramic setter and sintered metal components

When to choose MIM, CNC, investment casting or powder pressing

Compare geometry, order quantities and finished dimensions before committing to tooling.

Evaluation criteriaMIMMulti-axis CNCInvestment castingPress-and-sinter PM
GeometrySmall 3D shapes, thin sections and side features where tooling permits.Profiles and fits where cutters can reach the feature.Complex shapes with room for casting radii and finishing stock.Profiles that can compact and eject along the press axis.
Volume and toolingRecurring orders can amortize the mold, setters and trial lots.Prototypes and early batches can start from stock with fixtures.Compare pattern tooling, yield and machining before setting lot size.Dedicated dies suit stable, repeatable high volumes.
Density, dimensions and surfaceMeasure sintered density; define machining and coating states for critical features.Verify stock condition, machined tolerances and tool marks.Agree casting defect criteria and finishing of mating areas.Verify density by location and any dimensional sizing step.

Process routes and DFM review

Feedstock and injection

  • Blend metal powder with a binder, then mold the green part. Review side actions, the gate, ejector marks and parting line before tooling.
  • Use gradual wall transitions and agree draft and witness locations on Class A faces and mating datums.

MIM alloys, tolerances and acceptance criteria

Choose an alloy to review its typical use and required evidence. Confirm the grade and condition before selecting tensile, hardness or density limits.

MIM-316L

Selection basis
Austenitic stainless steel for corrosion-sensitive housings, buckles and quick-release parts.
What to verify
Agree the as-sintered or finished condition and corrosion test. Verify any magnetic requirement on the finished part.
What to verifyDrawing or trial referenceAcceptance method
Linear dimensions±0.3%–±0.5% as-sintered for initial review; ±0.025 mm as a target for selected post-machined features.Check length, datum, repeatability and final condition by cavity on the first article.
Density and metallographic porosityAgree bulk density by alloy separately from any sectional porosity target, such as ≤0.5%.Specify immersion method, cut location, field count and how the area fraction is reported.
Wall thickness and shrinkageUse 0.5–6.0 mm wall thickness and 15%–20% linear shrinkage as starting points for review.Verify feedstock-specific shrinkage, wall transitions, support and warpage through trials.
Flatness and straightnessState the controlled surface, span and final treatment state on the drawing.Agree free-state or fixtured measurement. Validate ceramic support and sizing where needed.

Technical references · ASTM B883 · ISO 22068 · MPIF Standard 35

Typical parts and inspection priorities

Representative applications and inspection plans.

Stainless watch buckle and quick-release part

MIM-316L: confirm fork symmetry, spring-bar hole alignment and gate location away from the visible face. Agree a mating gauge and a finish sample for mirror polish or PVD.

Loaded lever and miniature gear

MIM-17-4PH: confirm tool release, profile or tooth geometry, and hardness and fit after the specified aging treatment.

Lightweight titanium structure

Ti-6Al-4V: check thin-wall distortion and ceramic support, and agree chemical, density and mechanical testing at trial stage.

Metallography, dimensional inspection and protective packing

Sectional porosity and immersion density

Embed and polish the agreed section for microscopy. Record location, field count and area fraction separately from bulk density by immersion. Set furnace-lot sampling during trial approval.

CMM, optical measurements and first article inspection

Select CMM, optical measurement or a gauge according to access and datum. Record cavity IDs and measurement condition. Agree sampling and any Cpk target on named characteristics.

Compartment trays and feature protection

Separate polished faces and protect threads where needed. Specify tray material, ESD properties if required, and the label linking each package to its production lot.

From drawing review to batch release

  1. Drawing review and DFM

    Review the STEP model and 2D drawing, grade, annual demand and secondary operations. Agree the quotation scope and the trial plan.

  2. Tooling and T1 trial

    Build the mold and setters for the selected feedstock, then mold and sinter the T1 samples to verify the initial shrinkage compensation.

    25–35 days · Tooling and T1 planning estimate

  3. First article and metallurgy

    Check cavity-by-cavity dimensions and fit. Submit agreed density, porosity and mechanical test results before approval.

  4. Production lot release

    Freeze the approved process revision, complete secondary work and dispatch with the agreed packing and inspection records.

Frequently asked questions

When should MIM be evaluated first?

Start with small, complex parts whose design is stable and whose recurring demand can cover mold and qualification costs. CNC prototypes can verify fit before tooling.

What information is needed before tooling?

Send the STEP model, 2D drawing with datums, target alloy and condition, annual and batch volumes, cosmetic zones, critical fits and inspection requests.

Does immersion density prove ≤0.5% metallographic porosity?

The two tests measure different properties. Specify both criteria separately, including the section locations and image analysis method for porosity.

How do I choose between 316L and 17-4PH?

Evaluate 316L for corrosion-sensitive parts. Evaluate aged 17-4PH when strength or hardness drives the decision. Agree the delivery condition and acceptance tests for the chosen grade.

Can titanium MIM be trialed in a small lot?

Trial feasibility depends on feedstock, minimum run size, wall geometry and the required oxygen, nitrogen and mechanical checks. Agree the sample and test plan before release.

Can gate, parting-line or ejector marks be removed?

First locate them away from cosmetic and sealing areas wherever feasible. Assess trimming, machining or polishing and approve limits with a sample.

Send drawings for engineering review

Send drawings and quantities with the selected route, alloy and finishing requirements for review.

Engineering review brief

Choose a process focus and describe the critical requirements. Your choices will be included in the enquiry.

Drawings & reference files

STEP/STP, PDF, JPG or PNG. Up to 3 files; 10 MB each, 20 MB total.

No files selected

    No drawing yet? Describe the part and application below.

    KEEPWIN · LANGUAGE

    Choose your language

    Select the language you prefer for your visit.

    You can change your language anytime in the menu.